All Pro RL706830E26WBS 5" & 6" LED Retrofit Kit

All Pro RL706830E26WBS 5" & 6" LED Retrofit Kit

The All-Pro RL706830E26WBS is a retrofit LED Module and Trim for 5” and 6” aperture recessed downlights. It is designed for use with compatible 5” and 6” housings including the Halo H25, H5, H27, H7, H7U series and All-Pro ET/EI500, ET/EI2700, ET/EI700. The RL7 with integral LED driver offers 120 volt dimming capability. The RL7 lens provides uniform illumination and wet location listing. The RL7 die-cast construction makes any housing AIR-TITE for added HVAC savings and code compliance.

The All-Pro RL706830E26WBS is a retrofit LED Module-Trim for 5” and 6” aperture recessed downlights. The RL706830E26WBS is designed for use with compatible 5” and 6” housings including the Halo H25, H5, H27, H7, H7U series and All-Pro ET/EI500, ET/EI2700, ET/EI700. The RL7 with integral LED driver offers 120 volt dimming capability. The RL7 lens provides uniform illumination and wet location listing. The RL7 die-cast construction makes any housing AIR-TITE for added HVAC savings and code compliance.

MECHANICAL Module-Trim

• Module construction includes LED, heat sink, reflector, lens,baffle and trim ring

• Durable die-cast aluminum construction

• Heat sink designed to conduct heat away from the LED keeping the junction temperatures below specified maximums, even when installed in insulated ceiling environments

• High Gloss Appliance White paint finish L ens

• Impact-resistant polycarbonate

• Convex form for lamp-like appearance

• High lumen transmission

• Diffusing for even illumination MOUNTING

Torsion Spring Brackets

• Precision formed steel torsion spring brackets secure torsion springs to fit compatible housings with torsion spring mounting tabs.

• Ac c e s sory ( inc luded) : 5” & 6” Friction Blade Kit: Stainless steel friction blades provide alternative to torsion springs for retrofit in 5” and 6” housings without torsion spring mounting tabs.

• Friction blade design allows the RL7 to be installed in any position within the housing aperture (360 degrees).

Housing Compatibility See Housing Compatibility section.

LED

• 636 lumens

• Color Temperature: 3000ฐK

• CRI: 81

• Lumen Maintenance: L70/50 70% lumens / 50,000 hours

• Efficacy 43.47 Lumens per Watt

• LED is a chip on board design consisting of a multiple LED package to create one virtual light source for a productive “cone of light” ELECTRICAL Powe r Conne c t ions

• E26 medium screw-base Edison connector provides easy retrofit of incandescent housings.

Ground Connection

• Separate grounding cable included on the RL7 module for attachment to the housing during installation.

LED Dr i v e r

• Dimmable driver is a120 Volt, high efficiency, electronic power supply providing DC power to the LED.

• Driver meets FCC EMI/RFI Consumer Level limits for use in residential and commercial installations.

• Driver features power factor >.90, THD <20% and has integral thermal protection in the event of over temperature or internal failure.

• Driver is specifically designed for compatibility with RL7 series LED.

• Driver mounts externally to the module, allowing future replacement, if needed.

Dimming

• The RL7 LED is dimmable to 15% with standard 120V electronic low voltage dimmers (recommended), and many incandescent / magnetic low voltage dimmers; and dims to 5% using dimmers with low end trim adjustment.

• Note: Standard incandescent dimmers require a minimum load of typically >40 watts on the circuit for full range dimming performance (four LED modules).

• Note: For dimming with digital (smart) multi-location dimmers or when dimming fewer than four LED modules, electronic low voltage dimmers are required (ELV dimmers need a neutral connection in the wallbox).

• Refer to dimming application notes, and refer to dimmer manufacturers for compatibility.

Warranty Cooper Lighting provides a three year limited warranty on RL7 LED.

COMPLIANCE Labels

• UL/cUL Listed

• UL/cUL Listed for DampLocation

• UL/cUL Listed for Wet Location – Shower Applications

• May be installed in housings in direct contact with airpermeable insulation and combustible material

Qualification

• ENERGY STARฎ qualified

• Can be used for International

Energy Conservation Code luminaire (IECC) high efficacy compliance IC and AIR-TITE™ Certified under ATSM-E283 and listed UL/cUL 1598. May be used to meet insulated ceiling and restricted air-flow requirements

such as:

• Washington State Energy Code 3 • International Energy Conservation Code (IECC)

• New York State Energy Conservation Construction Code (NY-ECCC)

• State of California Title 24 “Recessed Luminaires in Insulated Ceilings.”